data sheet DL100-7PCBA3 dual axis psd sum and difference amplifier specification 5700 corsa avenue, #105 ? westlake village, ca 91362 tel: (818) 706-3400 ? fax (818) 889-7053 email: sales@pacific-sensor.com ? www.pacific-sensor.com mechanical outline all dimensions in inches block diagram ? phdbias (optional) pin 1 v(y) difference pin 3 v(y) sum pin 5 +15v pin 7 ?15v pin 9 analog ground pin 8 v(x) difference pin 4 v(x) sum pin 6 + phdbias (optional) pin 2 anode 1 0.13 0.10 dia 2 places 1.65 0.13 0.13 0.56 y optical center pin 1 2 3 4 5 6 7 8 9 function optional ?bias optional +bias y voltage out x voltage out anode sum (y) cathode sum (x) +15 volts signal and power common ?15 volts 0.13 0.065 1.13 0.76 1 2 3 4 5 6 7 8 9 pins 1-9 on 0.100" centers anode 2 diff +15v ?15v ?15v j1 agnd sum diff sum +15v cathode 1 cathode 2 pss-dl100-7-cer j2 the DL100-7PCBA3 is a dual axis position sensing diode with sum and difference amplifiers. it contains internal bias circuitry of 14.3 volts for the position sensing diode, or the user can externally apply a bias voltage. the board has a 9 pin connector for easy hook up. outputs are bipolar voltage analogs of the x and y position of the light spot centroid, as well as the total x current and the total y current. the sum outputs may be used to externally normalize the x and y difference outputs. by normalizing the x and y signals, they become independent of fluctuations in light spot intensity. specifications power supply voltage v s : min 10 volts; max 18 volts; recommended 15 volts maximum output voltage: +v s ?3; ?v s +3 maximum output current limit: 25 ma maximum external bias: ?v s ?10 volts; +v s +10 volts maximum slew rate: 10 volts per microsecond theoretical noise: 15 nv h z ?1/2 operating temperature: 0 to 70c ?3db bandwidth: 257 khz resolution (bias dependent): 0.5 m linearity (bias dependent): 1% of full scale maximum light intensity: 1.5 w/cm 2 see dl100-7pcba application notes. version: 111306 page 1 of 3
data sheet DL100-7PCBA3 dual axis psd sum and difference amplifier specification 5700 corsa avenue, #105 ? westlake village, ca 91362 tel: (818) 706-3400 ? fax (818) 889-7053 email: sales@pacific-sensor.com ? www.pacific-sensor.com page 2 of 3 application notes description the DL100-7PCBA3 is a duolateral position sensing module composed of a 10mm x 10mm active area position sensing photodiode and associated circuitry. it senses the position of a light spot on the surface of the photodiode and provides the voltage analogs of the x, y and spot intensity. the sensing diode is made using silicon technology and consequently responds to light at wavelengths between 400nm and 1100nm. the output, as a function of wavelength, follows our typical C7 process silicon photodiode responsivity curve. psds duolateral position sensing diodes are photodiodes with electrodes placed at the edges of the photodiode. two resistive sheets cover the pn junction, with one sheet on top and one sheet on the bottom. as light impinges on the photodiode, the pn junction generates a current at the centroid of the light power density. the current from this generator separates at the top resistive sheet according to ohm's law, and electrodes at opposite ends collect the individual currents. the response at the bottom sheet layer is similar to the top sheet except that the current is in the opposite direction. the bottom electrodes are placed at edges orthogonal to the top electrodes. outputs the DL100-7PCBA3 module contains amplifiers that convert the light generated currents into voltages. the voltages are then processed to provide a bipolar signal for the x axis and a bipolar signal for the y axis. the currents are further processed to provide a voltage for the total x current and the total y current. these voltages represent the light intensity. note: the x sum output voltage is negative, the y sum output is positive. psd biasing position sensing diodes of the type used in the DL100-7PCBA3 module are more accurate if a reverse bias is applied across the diode. installing jumpers j1 and j2 will engage circuitry that creates and applies a reverse bias of 14.3 volts (with +/-15v supply). in this configuration, there should be no connection to pins 1 and 2. for bias voltages other than 14.3v, remove jumpers j1 and j2 and hook up an external bias source to pins 1 and 2. (for zero bias operation, just remove the jumpers. no connection is necessary to pins 1 and 2). although reduced bias will degrade the linearity performance of the psd, voltage offset and noise can be improved. determining the optimum bias voltage for each application is usually a trial and error procedure. if determining positions over a large area of the psd is required, the built-in 14.3v bias is probably the best option. if low light levels and/or small incremental movement over a small area of the psd are the application, then zero to low bias voltage may work best. effects of light spot shape, size and intensity since the photodiode current appears to be generated at the centroid of the light spot power density, it is the centroid location that is tracked by the voltage outputs. if any of the light spot is off the photodiode then the centroid of the light that does fall in the diode is the location tracked. the ultimate resolution of the position sensor is signal to noise limited. consequently, the spot intensity should be as great as possible without causing damage to the photodiode. there is a limit to the intensity. the spot size and intensity should not concentrate the beam such that the light power locally heats the detector surface above about 110c. in practice the light intensity should never exceed 1.5w/cm 2 . many applications use an intensity of 1 to 3 milliwatts for a spot size of 1mm 2 . the current outputs of the photodiode are dependent on the light intensity and as a result the voltage outputs are also dependent on light intensity. if the beam source changes intensity when the spot location is being sensed, then the output should be normalized using the sum signals available on the DL100-7PCBA3. normalization is accomplished externally by dividing the location voltage by the sum voltage for the layer (x or y) being measured. the DL100-7PCBA3 does not normalize the location output signals.
data sheet DL100-7PCBA3 dual axis psd sum and difference amplifier specification 5700 corsa avenue, #105 ? westlake village, ca 91362 tel: (818) 706-3400 ? fax (818) 889-7053 email: sales@pacific-sensor.com ? www.pacific-sensor.com page 3 of 3 application notes ambient light considerations ambient light can cause errors and reduced resolution. if the ambient light is of homogeneous power density over the entire diode surface it will appear as a current source at the diode center. since this apparent current source adds to the signal current the overall current is increased. the differencing circuits will eliminate this current from the x, y outputs but it will still be included in the sum circuit outputs. if the beam to be tracked is monochromatic, or nearly so, a bandpass filter can be placed in front of the diode to eliminate most of the ambient light. if the ambient light contains shadows that fall on the diode surface, the apparent current source will be off center and will contribute to an offset in the position outputs as well as contributing to the sum outputs. again, an optical filter can eliminate or reduce most of these undesirable effects. if the ambient light contains shadows that are changing with time then the position outputs and the sum circuit outputs will also show a time varying signal that is related to the shifting ambient light. resolution best resolution is obtained with the maximum allowable light intensity and optimum wavelength. the temperature should be held within specification. resolution obtainable under specified conditions is 0.5m or less. speed of response increasing the psd bias voltage will increase the speed of the DL100-7PCBA3. the internally created reverse bias of 14.3v is sufficient for most applications. as noted above, pins 1 and 2 are provided to reduce or increase the 14.3v reverse bias, but biasing above 14.3v provides only a small increase in speed. care should be taken not to exceed the circuit common mode values and the breakdown voltage of the diode. see the DL100-7PCBA3 data sheet for maximum values. the rise and fall time of the DL100-7PCBA3 module with the 1cm 2 dl100-7-cer diode is better than 5s. linearity linearity improves with increased reverse bias. the 14.3v bias provided by the DL100-7PCBA3 module gives a linearity of 1 percent of full scale or better. temperature considerations the operating temperature must be between 0 to 70c. for best resolution the temperature should be kept at or below 25c. thermal gradients across the detector will cause position errors and should be avoided. offsets precision components are used in the circuitry but as much as 100 millivolts of offset may still be present in the outputs. if this causes a problem the offsets should be removed externally.
|
